Encrypting your link and protect the link from viruses, malware, thief, etc! Made your link safe to visit.

Problem 3 In an FSK system using coherent detection, the signals s) and s2() representing binary symbols 1 and 0, respectively, are defined by ,2 Assuming that fe > Af, show that the correlation coefficient of the signals si(t) and s2(t) is approximately given by 1()8201) dr 0 sinc(2Ay.Tb T. 1C1) d a. What is the minimum value of frequency shift for which the signals si(t) and s2(t) are orthogonal? b. What is the value of Af that minimizes the average probability of symbol error? . For the value of Af obtained in part c, determine the increase in E/No required so that this FSK scheme has the same noise performance as a binary PSK scheme system, also using coherent detection

 

Question:


Problem 3 In an FSK system using coherent detection, the signals s) and s2() representing binary symbols 1 and 0, respectively, are defined by ,2 Assuming that fe > Af, show that the correlation coefficient of the signals si(t) and s2(t) is approximately given by 1()8201) dr 0 sinc(2Ay.Tb T. 1C1) d a. What is the minimum value of frequency shift for which the signals si(t) and s2(t) are orthogonal? b. What is the value of Af that minimizes the average probability of symbol error? . For the value of Af obtained in part c, determine the increase in E/No required so that this FSK scheme has the same noise performance as a binary PSK scheme system, also using coherent detection

Show transcribed image text

Answer:


ANSwER iven at → FSK Sgte Sstem u uking coherent detection Yepresentin binar Symbol F o s, lt) an appiozimately iven b 0 Sinc [asp.Tb)

ST

Shorten Link Whatchamacallit Candy

Search This Blog

Powered by Blogger

Labels

Report Abuse

QUESTION 6 (a) The bar shown in Figure Q2(a) is subjected to tensile load of 150 Kn. If the stress in the middle portions is limited to 160 N/mm², determine the diameter of the middle portion. Find also the length of the middle portion if the total elongation of the bar is to be 0.25 mm. E E = 2.0 + 105N/mm². (12 marks) 150 KN 10 cm DIA 10 cm DIA 150 KN 45 cm Figure Q6(a) (b) A brass bar, having cross-section area of 900 mm², is subjected to axial forces as shown in Figure Q2(b), in which AB = 0.6 m, BC = 0.8 m, and CD = 1.0 m. Find the total elongation of the bar. E = 1.0 + 105N/mm2 . (8 marks) Page 4 of 5 B D 40 KN 70 KN 20 KN 10 KN Figure Q6(b) (TOTAL = 20 MARKS)

-
  Question: Show transcribed image text Answer:
Image

Question: A 250-V, 4-pole, wave-wound d.c. series motor has 782 conductors on itsarmature. It has armature and series field resistance of 0.75 ohm. The motor takesa current of 40 A. Estimate its speed and gross torque developed if it has a flux per pole of 25 mWb Answer: Step 1 Mechanical Engineering homework question answer, step 1, image 1 Mechanical Engineering homework question answer, step 1, image 2 Step 2 Mechanical Engineering homework question answer, step 2, image 1 Step 3 Mechanical Engineering homework question answer, step 3, image 1

-
Question: A 250-V, 4-pole, wave-wound d.c. series motor has 782 conductors on itsarmature. It has armature and series field resistance of 0.75 ohm. The motor takesa current of 40 A. Estimate its speed and gross torque developed if it has a flux per pole of 25 mWb Answer: Step 1 Step 2 Step 3
Image

Contributors